Electric Circuit Lab
Build a circuit with cells, a switch and bulbs. Compare series and parallel connections and see how voltage and current change the brightness.
- physics
- beginner
- 15 minutes
- Minutes
- 15
- Tasks
- 7
- Goals
- 6
- Badges
- 1
About this experience
What you will learn and do
Learning objectives
- Explain why a circuit must be complete for current to flow.
- Compare bulbs connected in series and in parallel.
- Describe how adding cells increases voltage and brightness.
- Recognise that too much voltage can damage a bulb.
- Use an ammeter and a voltmeter and work out resistance with R = V ÷ I.
- Explain why a filament lamp does not obey Ohm's law.
Skills you will build
- Observation
- Cause and effect
- Scientific reasoning
Interactive practical
↑ Back to overviewVirtual lab · Physics
Set-up
Each cell has an internal resistance of 0.3 Ω.
1 bulb in series
Drag to rotate · scroll or pinch to zoom
Meters
The circuit is open, so both meters read zero.
Series
One path. The same current flows through every bulb. The battery voltage is shared between the bulbs, so each is dimmer. Total resistance: R = R₁ + R₂ + R₃.
I = same everywhere · V = V₁ + V₂ + …
Parallel
Each bulb has its own branch across the battery, so each gets the full voltage and stays bright. The branch currents add up. Total resistance is less than any single branch.
V = same across each branch · I = I₁ + I₂ + …
Ohm's law and power
For a resistor at constant temperature, V = I × R. The power used is P = V × I.
V = IR · R = V ÷ I · P = VI
A real battery and a real lamp
Each cell has a little internal resistance, so the terminal voltage falls as the current rises ("lost volts"). A filament lamp gets hotter as the current rises, so its resistance increases and its V–I graph curves.
Meter readings
0 of 12 readingsClose the switch, then press Record reading. The meters carry a small error of about 1 %, like real ones. For the lamp's V–I curve use one bulb in series and change the rheostat and the number of cells to get at least six different currents.
| # | Set-up | I (A) | V (V) | R = V ÷ I (Ω) | P (W) |
|---|---|---|---|---|---|
| No readings yet. | |||||
Start with one bulb in series and take a reading.
Lamp: voltage against current
Calculation practice
0 of 0 correctA battery of e.m.f. 6 V and internal resistance 0.5 Ω is connected to a 5 Ω resistor. Calculate the voltage across the 5 Ω resistor (the terminal voltage).
Formulas: V = IR · P = VI · series R = R₁ + R₂ · parallel 1/R = 1/R₁ + 1/R₂ · e.m.f. E = V + Ir
Tasks
0 of 7 · 0 pts- Complete the circuitNot completed yet
Close the switch so current can flow round the circuit.
- Bulbs in seriesNot completed yet
Add a second bulb in series and notice how bright each one is.
- Bulbs in parallelNot completed yet
Connect two or more bulbs in parallel and compare their brightness with series.
- More cells, brighter bulbNot completed yet
Use one bulb in series and raise the battery to 3 cells without blowing it.
- Overload challengeoptionalNot completed yet
Find out what happens when the voltage is too high for one bulb.
- Record six meter readingsoptionalNot completed yet
Take six readings of current and voltage with the ammeter and voltmeter.
- Find the lamp's curveoptionalNot completed yet
Take at least five single-bulb readings over a wide range of current and see the resistance rise.
Check your understanding
0 of 20Finish the tasks to unlock the questions.
Method
- Build the circuit with the switch open.
- Put the ammeter in series and the voltmeter across the bulb.
- Close the switch and read both meters.
- Change the rheostat and record again, then compute R = V ÷ I.
- Plot V against I and describe the shape.
Safety
- Open the switch when changing connections.
- Do not exceed a bulb's rated voltage.
Key ideas
- Current
- The rate of flow of charge, in amperes.
- Voltage
- The energy given to each unit of charge, in volts.
- Resistance
- How much a component opposes the current, in ohms.