Electrolysis
Pass electricity through different liquids, find what forms at each electrode, then measure the amount and check it with Faraday's law.
- chemistry
- advanced
- 20 minutes
- Minutes
- 20
- Tasks
- 7
- Goals
- 4
- Badges
- 1
About this experience
What you will learn and do
Learning objectives
- Define electrolysis.
- Predict the products at each electrode.
- Explain copper purification and electroplating.
- Use charge = current × time and Faraday's law to calculate the amount deposited.
Skills you will build
- Prediction
- Investigation
- Scientific reasoning
Interactive practical
↑ Back to overviewVirtual lab · Chemistry
Set-up
02 V needed12
Changing the current starts the run again.
The cell is off. Set the voltage to 2 V or more.
Dilute sulfuric acid
Drag to rotate · scroll or pinch to zoom
Cathode 2H⁺ + 2e⁻ → H₂
Anode 4OH⁻ → 2H₂O + O₂ + 4e⁻
Ions in dilute sulfuric acid
H⁺SO₄²⁻OH⁻ (from water)
Electrochemical series: easier to discharge →
- K
- Na
- Ca
- Mg
- Al
- Zn
- Fe
- Pb
- H
- Cu
- Ag
When two positive ions are present, the one lower in the series (further right) is discharged at the cathode.
The solution: Water is used up, so the acid becomes more concentrated.
Cathode (−)
2H⁺ + 2e⁻ → H₂
Colourless bubbles at the cathode.
Test: Burns with a squeaky pop when a lighted splint is held to it.
Why: Only H⁺ can be discharged at the cathode, so hydrogen forms.
Anode (+)
4OH⁻ → 2H₂O + O₂ + 4e⁻
Colourless bubbles at the anode.
Test: Relights a glowing splint.
Why: OH⁻ is discharged in preference to SO₄²⁻, so oxygen forms.
Measurements
0 of 8 readingsSwitch the cell on, let it run, then press Record reading. The gas is read from the collecting tube, so your numbers carry a small measuring error, just like a real experiment. Take at least three readings at different times.
| t (min) | I (A) | Q (C) | Cathode (cm³) | Anode (cm³) |
|---|---|---|---|---|
| No readings yet. | ||||
Start with a short run, record, then let more time pass and record again.
Cathode amount against charge
Calculation practice
0 of 0 correctA copper(II) sulfate cell and a silver nitrate cell are connected in series, so the same charge passes through both. 0.47 g of copper is deposited in the first cell. What mass of silver is deposited in the second? (1 Faraday = 96 500 C; Cu = 63.5, Ag = 108; molar volume of a gas = 24 dm³ at r.t.p.)
Constants: 1 Faraday = 96 500 C; Cu = 63.5; Ag = 108; 1 mol of gas = 24 dm³ (24 000 cm³) at r.t.p.
Tasks
0 of 7 · 0 pts- Switch onNot completed yet
Raise the supply voltage to 2 V or more so the cell conducts.
- Split waterNot completed yet
Electrolyse dilute sulfuric acid for 5 minutes and see hydrogen and oxygen collect.
- Copper platingNot completed yet
Electrolyse copper(II) sulfate with graphite electrodes for 5 minutes and coat the cathode with copper.
- Purify copperNot completed yet
Use copper electrodes in copper(II) sulfate and watch the anode dissolve.
- Make chlorineoptionalNot completed yet
Electrolyse concentrated sodium chloride solution with graphite electrodes.
- Silver platingoptionalNot completed yet
Electrolyse silver nitrate and coat the cathode with silver.
- Take three readingsoptionalNot completed yet
Record the amount collected at three different times and see that it is proportional to the charge.
Check your understanding
0 of 20Finish the tasks to unlock the questions.
Experiment guide
- Pour dilute sulfuric acid into the beaker and place the two electrodes in it.
- Connect them to the supply through an ammeter and a rheostat. The anode joins the positive terminal.
- Switch on and set the current with the rheostat. Keep it steady.
- Note the time. Read the gas volumes in the collecting tubes.
- Record at several times and compare the amount collected with the charge, Q = I × t.
Safety
- Wear goggles. Dilute acids can irritate the skin and eyes.
- Chlorine is poisonous: use a fume cupboard or very small amounts.
- Never test hydrogen near a flame in a large volume.
Key ideas
- Electrolyte
- A molten or dissolved compound with ions free to move.
- Cathode and anode
- The cathode (−) attracts positive ions, which gain electrons. The anode (+) attracts negative ions, which lose electrons.
- Faraday
- One mole of electrons carries 96,500 C. Charge Q = current × time in seconds.
- Amount deposited
- Moles of electrons ÷ electrons per ion × molar mass. For example Cu²⁺ needs 2 mol of electrons per mole of copper.